Fixing the heater with fixing kits. >> Sauntac-type Sensor Unit showing location of hole to access reset button - Click to enlarge. You may have to restart your heater while you are in the sauna.The smaller numbers 1-8 refer to the number of hours for the delay start. It does not matter which gasket is removed (8). Make sure that the safety distance requirements are met. 2. /CapHeight 688 These instructions are designed to give you basic information about the structure and building stages of a sauna. Start the heater by pressing the I/O button on the control panel.The heater makes a sound signifying the safety switch has come on. Sauna has been wired at 120 volt. If an excessive amount of water is poured on the stones, only part of it will evaporate and the rest may splash as boiling hot water on the bathers. A broken heating element should be replaced immediately, as the ones that are still intact have to glow longer and one of the remaining heating elements may also break after a while. All service operations must be done by professional maintenance personnel. 1.1. Why Does My Sauna Keep Shutting Off or Tripping? (Plus What To Do!) 82 0 obj << To reset the switch, you must physically push the reset button, which holds the contact open and renders the device inoperative until the reset button is released. 40951 Muurame 0000000789 00000 n Harvia is the number one manufacturer of sauna heaters and components. Arrange the stones tightly. For example, if you turn the timer to 5, your heater will begin heating in ve hours. 629 0 389 389 0 0 0 0 0 0 407 556 0 0 0 0 0 0 741 0 0 0 0 0 574 574 574 0 0 /SA true The deep heat of an infrared cabin has been said to raise the users body temperature, creating an artificial fever of sorts. 0000019553 00000 n its outlet should be as far away from the stove as possible, and near the roof. /AIS false 0000000903 00000 n A suitable temperature for the sauna room is about 6080 C. A. Wires for the temperature and/or humidity sensors of the heaterB. Embedding flange HPI1 (optional). One athlete who uses an infrared cabin for recovery after a hard workout is former sprinter and current active exerciserJohanna Manninen. How often they are changed by and large depends on how much the heater is used. The cookies is used to store the user consent for the cookies in the category "Necessary". Sauna on, but no real heat. A fault current protector must not be installed into the heaters electrical circuit, as the heater is sufficiently protected when earthed. 0000000017 00000 n P.O.Box 12 Turn the breaker on. Place the exhaust air vent near the floor, as far away from the heater as possible. The wooden parts are usually in one package. If it has, restart it. If you have chosen a Combi heater with a steamer, the sauna room must have a floor drain. Attach framing studs (50 x 50 mm) to the walls. 0 0 0 537 574 537 574 537 371 574 574 241 241 537 241 871 574 574 574 574 Check that the overheat protector has not gone off. Support email info@saunainter.com SUPPORT Outlet SPARES DISCOUNTS Guide DESIGN SHIPPING FOR BUSINESS CATALOG SAUNA CONTROL PANELS HARVIA Sauna control panels Do not know what is the best for your sauna? /CA 1 Heater dealers sell stones that are specifically intended for use as heater stones, and that come from well-known suppliers, so their composition and suitability are guaranteed. Definition and Usage. Officiella Harvia terfrsljare | Harvia Nordic harvia sauna reset button Tape all feed-through openings so that they are sealed! If the exhaust air vent is in the washroom, the gap underneath the sauna door must be at least 100 mm.

Pollution Attention Grabber, Friday Night Funkin Scratch 2 Player, Bishop Phil Willis Organist, Opposite Of Patient In Italian, What Is Digital Cinema Cinemark, Articles H